????
Your IP : 3.23.103.14
NETWORK-SERVICES-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, Counter32, Gauge32, MODULE-IDENTITY, mib-2
FROM SNMPv2-SMI
TimeStamp, TEXTUAL-CONVENTION
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB;
application MODULE-IDENTITY
LAST-UPDATED "200003030000Z"
ORGANIZATION "IETF Mail and Directory Management Working Group"
CONTACT-INFO
" Ned Freed
Postal: Innosoft International, Inc.
1050 Lakes Drive
West Covina, CA 91790
US
Tel: +1 626 919 3600
Fax: +1 626 919 3614
E-Mail: ned.freed@innosoft.com"
DESCRIPTION
"The MIB module describing network service applications"
REVISION "200003030000Z"
DESCRIPTION
"This revision, published in RFC 2788, changes a number of
DisplayStrings to SnmpAdminStrings. Note that this change
is not strictly supported by SMIv2. However, the alternative
of deprecating the old objects and defining new objects
would have a more adverse impact on backward compatibility
and interoperability, given the particular semantics of
these objects. The defining reference for distinguished
names has also been updated from RFC 1779 to RFC 2253."
REVISION "199905120000Z"
DESCRIPTION
"This revision fixes a few small technical problems found
in previous versions, mostly in regards to the conformance
groups for different versions of this MIB. No changes have
been made to the objects this MIB defines since RFC 2248."
REVISION "199708170000Z"
DESCRIPTION
"This revision, published in RFC 2248, adds the
applDescription and applURL objects, adds the quiescing
state to the applOperStatus object and renames the MIB
from the APPLICATION-MIB to the NETWORK-SERVICE-MIB."
REVISION "199311280000Z"
DESCRIPTION
"The original version of this MIB was published in RFC 1565"
::= {mib-2 27}
-- Textual conventions
-- DistinguishedName is used to refer to objects in the
-- directory.
DistinguishedName ::= TEXTUAL-CONVENTION
DISPLAY-HINT "255a"
STATUS current
DESCRIPTION
"A Distinguished Name represented in accordance with
RFC 2253, presented in the UTF-8 charset defined in
RFC 2279."
SYNTAX OCTET STRING (SIZE (0..255))
-- Uniform Resource Locators are stored in URLStrings.
URLString ::= TEXTUAL-CONVENTION
DISPLAY-HINT "255a"
STATUS current
DESCRIPTION
"A Uniform Resource Locator represented in accordance
with RFCs 1738 and 2368, presented in the NVT ASCII
charset defined in RFC 854."
SYNTAX OCTET STRING (SIZE (0..255))
-- The basic applTable contains a list of the application
-- entities.
applTable OBJECT-TYPE
SYNTAX SEQUENCE OF ApplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table holding objects which apply to all different
kinds of applications providing network services.
Each network service application capable of being
monitored should have a single entry in this table."
::= {application 1}
applEntry OBJECT-TYPE
SYNTAX ApplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry associated with a single network service
application."
INDEX {applIndex}
::= {applTable 1}
ApplEntry ::= SEQUENCE {
applIndex
INTEGER,
applName
SnmpAdminString,
applDirectoryName
DistinguishedName,
applVersion
SnmpAdminString,
applUptime
TimeStamp,
applOperStatus
INTEGER,
applLastChange
TimeStamp,
applInboundAssociations
Gauge32,
applOutboundAssociations
Gauge32,
applAccumulatedInboundAssociations
Counter32,
applAccumulatedOutboundAssociations
Counter32,
applLastInboundActivity
TimeStamp,
applLastOutboundActivity
TimeStamp,
applRejectedInboundAssociations
Counter32,
applFailedOutboundAssociations
Counter32,
applDescription
SnmpAdminString,
applURL
URLString
}
applIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index to uniquely identify the network service
application. This attribute is the index used for
lexicographic ordering of the table."
::= {applEntry 1}
applName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name the network service application chooses to be
known by."
::= {applEntry 2}
applDirectoryName OBJECT-TYPE
SYNTAX DistinguishedName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Distinguished Name of the directory entry where
static information about this application is stored.
An empty string indicates that no information about
the application is available in the directory."
::= {applEntry 3}
applVersion OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version of network service application software.
This field is usually defined by the vendor of the
network service application software."
::= {applEntry 4}
applUptime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the network service
application was last initialized. If the application was
last initialized prior to the last initialization of the
network management subsystem, then this object contains
a zero value."
::= {applEntry 5}
applOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
halted(3),
congested(4),
restarting(5),
quiescing(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the operational status of the network service
application. 'down' indicates that the network service is
not available. 'up' indicates that the network service
is operational and available. 'halted' indicates that the
service is operational but not available. 'congested'
indicates that the service is operational but no additional
inbound associations can be accommodated. 'restarting'
indicates that the service is currently unavailable but is
in the process of restarting and will be available soon.
'quiescing' indicates that service is currently operational
but is in the process of shutting down. Additional inbound
associations may be rejected by applications in the
'quiescing' state."
::= {applEntry 6}
applLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time the network service
application entered its current operational state. If
the current state was entered prior to the last
initialization of the local network management subsystem,
then this object contains a zero value."
::= {applEntry 7}
applInboundAssociations OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of current associations to the network service
application, where it is the responder. An inbound
association occurs when another application successfully
connects to this one."
::= {applEntry 8}
applOutboundAssociations OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of current associations to the network service
application, where it is the initiator. An outbound
association occurs when this application successfully
connects to another one."
::= {applEntry 9}
applAccumulatedInboundAssociations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of associations to the application entity
since application initialization, where it was the responder."
::= {applEntry 10}
applAccumulatedOutboundAssociations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of associations to the application entity
since application initialization, where it was the initiator."
::= {applEntry 11}
applLastInboundActivity OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this application last
had an inbound association. If the last association
occurred prior to the last initialization of the network
subsystem, then this object contains a zero value."
::= {applEntry 12}
applLastOutboundActivity OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this application last
had an outbound association. If the last association
occurred prior to the last initialization of the network
subsystem, then this object contains a zero value."
::= {applEntry 13}
applRejectedInboundAssociations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of inbound associations the application
entity has rejected, since application initialization.
Rejected associations are not counted in the accumulated
association totals. Note that this only counts
associations the application entity has rejected itself;
it does not count rejections that occur at lower layers
of the network. Thus, this counter may not reflect the
true number of failed inbound associations."
::= {applEntry 14}
applFailedOutboundAssociations OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number associations where the application entity
is initiator and association establishment has failed,
since application initialization. Failed associations are
not counted in the accumulated association totals."
::= {applEntry 15}
applDescription OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A text description of the application. This information
is intended to identify and briefly describe the
application in a status display."
::= {applEntry 16}
applURL OBJECT-TYPE
SYNTAX URLString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A URL pointing to a description of the application.
This information is intended to identify and describe
the application in a status display."
::= {applEntry 17}
-- The assocTable augments the information in the applTable
-- with information about associations. Note that two levels
-- of compliance are specified below, depending on whether
-- association monitoring is mandated.
assocTable OBJECT-TYPE
SYNTAX SEQUENCE OF AssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table holding a set of all active application
associations."
::= {application 2}
assocEntry OBJECT-TYPE
SYNTAX AssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry associated with an association for a network
service application."
INDEX {applIndex, assocIndex}
::= {assocTable 1}
AssocEntry ::= SEQUENCE {
assocIndex
INTEGER,
assocRemoteApplication
SnmpAdminString,
assocApplicationProtocol
OBJECT IDENTIFIER,
assocApplicationType
INTEGER,
assocDuration
TimeStamp
}
assocIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index to uniquely identify each association for a network
service application. This attribute is the index that is
used for lexicographic ordering of the table. Note that the
table is also indexed by the applIndex."
::= {assocEntry 1}
assocRemoteApplication OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the system running remote network service
application. For an IP-based application this should be
either a domain name or IP address. For an OSI application
it should be the string encoded distinguished name of the
managed object. For X.400(1984) MTAs which do not have a
Distinguished Name, the RFC 2156 syntax 'mta in
globalid' used in X400-Received: fields can be used. Note,
however, that not all connections an MTA makes are
necessarily to another MTA."
::= {assocEntry 2}
assocApplicationProtocol OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An identification of the protocol being used for the
application. For an OSI Application, this will be the
Application Context. For Internet applications, OID
values of the form {applTCPProtoID port} or {applUDPProtoID
port} are used for TCP-based and UDP-based protocols,
respectively. In either case 'port' corresponds to the
primary port number being used by the protocol. The
usual IANA procedures may be used to register ports for
new protocols."
::= {assocEntry 3}
assocApplicationType OBJECT-TYPE
SYNTAX INTEGER {
uainitiator(1),
uaresponder(2),
peerinitiator(3),
peerresponder(4)}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This indicates whether the remote application is some type of
client making use of this network service (e.g., a Mail User
Agent) or a server acting as a peer. Also indicated is whether
the remote end initiated an incoming connection to the network
service or responded to an outgoing connection made by the
local application. MTAs and messaging gateways are
considered to be peers for the purposes of this variable."
::= {assocEntry 4}
assocDuration OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this association was
started. If this association started prior to the last
initialization of the network subsystem, then this
object contains a zero value."
::= {assocEntry 5}
-- Conformance information
applConformance OBJECT IDENTIFIER ::= {application 3}
applGroups OBJECT IDENTIFIER ::= {applConformance 1}
applCompliances OBJECT IDENTIFIER ::= {applConformance 2}
-- Compliance statements
applCompliance MODULE-COMPLIANCE
STATUS obsolete
DESCRIPTION
"The compliance statement for RFC 1565 implementations
which support the Network Services Monitoring MIB
for basic monitoring of network service applications.
This is the basic compliance statement for RFC 1565."
MODULE
MANDATORY-GROUPS {applRFC1565Group}
::= {applCompliances 1}
assocCompliance MODULE-COMPLIANCE
STATUS obsolete
DESCRIPTION
"The compliance statement for RFC 1565 implementations
which support the Network Services Monitoring MIB
for basic monitoring of network service applications
and their associations."
MODULE
MANDATORY-GROUPS {applRFC1565Group, assocRFC1565Group}
::= {applCompliances 2}
applRFC2248Compliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for RFC 2248 implementations
which support the Network Services Monitoring MIB
for basic monitoring of network service applications."
MODULE
MANDATORY-GROUPS {applRFC2248Group}
::= {applCompliances 3}
assocRFC2248Compliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for RFC 2248 implementations
which support the Network Services Monitoring MIB for
basic monitoring of network service applications and
their associations."
MODULE
MANDATORY-GROUPS {applRFC2248Group, assocRFC2248Group}
::= {applCompliances 4}
applRFC2788Compliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for RFC 2788 implementations
which support the Network Services Monitoring MIB
for basic monitoring of network service applications."
MODULE
MANDATORY-GROUPS {applRFC2788Group}
::= {applCompliances 5}
assocRFC2788Compliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for RFC 2788 implementations
which support the Network Services Monitoring MIB for
basic monitoring of network service applications and
their associations."
MODULE
MANDATORY-GROUPS {applRFC2788Group, assocRFC2788Group}
::= {applCompliances 6}
-- Units of conformance
applRFC1565Group OBJECT-GROUP
OBJECTS {
applName, applVersion, applUptime, applOperStatus,
applLastChange, applInboundAssociations,
applOutboundAssociations, applAccumulatedInboundAssociations,
applAccumulatedOutboundAssociations, applLastInboundActivity,
applLastOutboundActivity, applRejectedInboundAssociations,
applFailedOutboundAssociations}
STATUS obsolete
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications. This is the original set
of such objects defined in RFC 1565."
::= {applGroups 7}
assocRFC1565Group OBJECT-GROUP
OBJECTS {
assocRemoteApplication, assocApplicationProtocol,
assocApplicationType, assocDuration}
STATUS obsolete
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications' associations. This is the
original set of such objects defined in RFC 1565."
::= {applGroups 2}
applRFC2248Group OBJECT-GROUP
OBJECTS {
applName, applVersion, applUptime, applOperStatus,
applLastChange, applInboundAssociations,
applOutboundAssociations, applAccumulatedInboundAssociations,
applAccumulatedOutboundAssociations, applLastInboundActivity,
applLastOutboundActivity, applRejectedInboundAssociations,
applFailedOutboundAssociations, applDescription, applURL}
STATUS deprecated
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications. This group was originally
defined in RFC 2248; note that applDirectoryName is
missing."
::= {applGroups 3}
assocRFC2248Group OBJECT-GROUP
OBJECTS {
assocRemoteApplication, assocApplicationProtocol,
assocApplicationType, assocDuration}
STATUS deprecated
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications' associations. This group
was originally defined by RFC 2248."
::= {applGroups 4}
applRFC2788Group OBJECT-GROUP
OBJECTS {
applName, applDirectoryName, applVersion, applUptime,
applOperStatus, applLastChange, applInboundAssociations,
applOutboundAssociations, applAccumulatedInboundAssociations,
applAccumulatedOutboundAssociations, applLastInboundActivity,
applLastOutboundActivity, applRejectedInboundAssociations,
applFailedOutboundAssociations, applDescription, applURL}
STATUS current
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications. This is the appropriate
group for RFC 2788 -- it adds the applDirectoryName object
missing in RFC 2248."
::= {applGroups 5}
assocRFC2788Group OBJECT-GROUP
OBJECTS {
assocRemoteApplication, assocApplicationProtocol,
assocApplicationType, assocDuration}
STATUS current
DESCRIPTION
"A collection of objects providing basic monitoring of
network service applications' associations. This is
the appropriate group for RFC 2788."
::= {applGroups 6}
-- OIDs of the form {applTCPProtoID port} are intended to be used
-- for TCP-based protocols that don't have OIDs assigned by other
-- means. {applUDPProtoID port} serves the same purpose for
-- UDP-based protocols. In either case 'port' corresponds to
-- the primary port number being used by the protocol. For example,
-- assuming no other OID is assigned for SMTP, an OID of
-- {applTCPProtoID 25} could be used, since SMTP is a TCP-based
-- protocol that uses port 25 as its primary port.
applTCPProtoID OBJECT IDENTIFIER ::= {application 4}
applUDPProtoID OBJECT IDENTIFIER ::= {application 5}
END