????
Your IP : 18.226.180.253
## automake - create Makefile.in from Makefile.am
## Copyright (C) 1994-2018 Free Software Foundation, Inc.
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2, or (at your option)
## any later version.
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
## GNU General Public License for more details.
## You should have received a copy of the GNU General Public License
## along with this program. If not, see <https://www.gnu.org/licenses/>.
?GENERIC_INFO?%SOURCE_SUFFIX%%DEST_SUFFIX%:
?!GENERIC_INFO?%DEST_INFO_PREFIX%%DEST_SUFFIX%: %SOURCE_INFO% %DEPS%
## It is wrong to have 'info' files dependent on %DIRSTAMP%, because
## 'info' files are distributed and %DIRSTAMP% isn't: a distributed file
## should never be dependent upon a non-distributed built file.
## Therefore we ensure that %DIRSTAMP% exists in the rule.
?!INSRC??DIRSTAMP? @test -f %DIRSTAMP% || $(MAKE) $(AM_MAKEFLAGS) %DIRSTAMP%
## Back up the info files before running makeinfo. This is the cheapest
## way to ensure that
## 1) If the texinfo file shrinks (or if you start using --no-split),
## you'll not be left with some dead info files lying around -- dead
## files which would end up in the distribution.
## 2) If the texinfo file has some minor mistakes which cause makeinfo
## to fail, the info files are not removed. (They are needed by the
## developer while he writes documentation.)
## *.iNN files are used on DJGPP. See the comments in install-info-am
%AM_V_MAKEINFO%restore=: && backupdir="$(am__leading_dot)am$$$$" && \
?INSRC? am__cwd=`pwd` && $(am__cd) $(srcdir) && \
rm -rf $$backupdir && mkdir $$backupdir && \
## If makeinfo is not installed we must not backup the files so
## 'missing' can do its job and touch $@ if it exists.
if ($(MAKEINFO) --version) >/dev/null 2>&1; then \
for f in $@ $@-[0-9] $@-[0-9][0-9] $(@:.info=).i[0-9] $(@:.info=).i[0-9][0-9]; do \
if test -f $$f; then mv $$f $$backupdir; restore=mv; else :; fi; \
done; \
else :; fi && \
?INSRC? cd "$$am__cwd"; \
if $(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS% \
?!INSRC? -o $@ `test -f '%SOURCE_INFO%' || echo '$(srcdir)/'`%SOURCE_INFO%; \
?INSRC??!GENERIC_INFO? -o $@ $(srcdir)/%SOURCE_INFO%; \
?INSRC??GENERIC_INFO? -o $@ $<; \
then \
rc=0; \
?INSRC? $(am__cd) $(srcdir); \
else \
rc=$$?; \
## Beware that backup info files might come from a subdirectory.
?INSRC? $(am__cd) $(srcdir) && \
$$restore $$backupdir/* `echo "./$@" | sed 's|[^/]*$$||'`; \
fi; \
rm -rf $$backupdir; exit $$rc
INFO_DEPS += %DEST_INFO_PREFIX%%DEST_SUFFIX%
?GENERIC?%SOURCE_SUFFIX%.dvi:
?!GENERIC?%DEST_PREFIX%.dvi: %SOURCE% %DEPS% %DIRSTAMP%
%AM_V_TEXI2DVI%TEXINPUTS="$(am__TEXINFO_TEX_DIR)$(PATH_SEPARATOR)$$TEXINPUTS" \
## Must set MAKEINFO like this so that version.texi will be found even
## if it is in srcdir (-I $(srcdir) is set in %MAKEINFOFLAGS%).
MAKEINFO='$(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS%' \
## texi2dvi doesn't silence everything with -q, redirect to /dev/null instead.
## We still want -q (%TEXIQUIET%) because it turns on batch mode.
## Use '--build-dir' so that TeX and Texinfo auxiliary files and build
## by-products are left in there, instead of cluttering the current
## directory (see automake bug#11146). Use a different build-dir for
## each file (and distinct from that of the corresponding PDF file) to
## avoid hitting a Texinfop bug that could cause low-probability racy
## failure when doing parallel builds; see:
## https://lists.gnu.org/archive/html/automake-patches/2012-06/msg00073.html
$(TEXI2DVI) %TEXIQUIET% --build-dir=$(@:.dvi=.t2d) -o $@ %TEXIDEVNULL% \
?GENERIC? %SOURCE%
?!GENERIC? `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%
?GENERIC?%SOURCE_SUFFIX%.pdf:
?!GENERIC?%DEST_PREFIX%.pdf: %SOURCE% %DEPS% %DIRSTAMP%
%AM_V_TEXI2PDF%TEXINPUTS="$(am__TEXINFO_TEX_DIR)$(PATH_SEPARATOR)$$TEXINPUTS" \
## Must set MAKEINFO like this so that version.texi will be found even
## if it is in srcdir (-I $(srcdir) is set in %MAKEINFOFLAGS%).
MAKEINFO='$(MAKEINFO) $(AM_MAKEINFOFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS%' \
## texi2pdf doesn't silence everything with -q, redirect to /dev/null instead.
## We still want -q (%TEXIQUIET%) because it turns on batch mode.
## Use '--build-dir' so that TeX and Texinfo auxiliary files and build
## by-products are left in there, instead of cluttering the current
## directory (see automake bug#11146). Use a different build-dir for
## each file (and distinct from that of the corresponding DVI file) to
## avoid hitting a Texinfop bug that could cause low-probability racy
## failure when doing parallel builds; see:
## https://lists.gnu.org/archive/html/automake-patches/2012-06/msg00073.html
$(TEXI2PDF) %TEXIQUIET% --build-dir=$(@:.pdf=.t2p) -o $@ %TEXIDEVNULL% \
?GENERIC? %SOURCE%
?!GENERIC? `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%
?GENERIC?%SOURCE_SUFFIX%.html:
?!GENERIC?%DEST_PREFIX%.html: %SOURCE% %DEPS% %DIRSTAMP%
## When --split (the default) is used, makeinfo will output a
## directory. However it will not update the time stamp of a
## previously existing directory, and when the names of the nodes
## in the manual change, it may leave unused pages. Our fix
## is to build under a temporary name, and replace the target on
## success.
%AM_V_MAKEINFO%rm -rf $(@:.html=.htp)
%SILENT%if $(MAKEINFOHTML) $(AM_MAKEINFOHTMLFLAGS) $(MAKEINFOFLAGS) %MAKEINFOFLAGS% \
?GENERIC? -o $(@:.html=.htp) %SOURCE%; \
?!GENERIC? -o $(@:.html=.htp) `test -f '%SOURCE%' || echo '$(srcdir)/'`%SOURCE%; \
then \
rm -rf $@ && mv $(@:.html=.htp) $@; \
else \
rm -rf $(@:.html=.htp); exit 1; \
fi
## If we are using the generic rules, we need separate dependencies.
## (Don't wonder about %DIRSTAMP% here, this is used only by non-generic
## rules.)
if %?GENERIC_INFO%
%DEST_INFO_PREFIX%%DEST_SUFFIX%: %SOURCE_REAL% %DEPS%
endif %?GENERIC_INFO%
if %?GENERIC%
%DEST_PREFIX%.dvi: %SOURCE_REAL% %DEPS%
%DEST_PREFIX%.pdf: %SOURCE_REAL% %DEPS%
%DEST_PREFIX%.html: %SOURCE_REAL% %DEPS%
endif %?GENERIC%